Hornit Horn Review

A Look at the Hornit, a horn with a difference.

The Hornit, great packaging, well designed, I really like the way the lads at Hornit has spent time on the packaging 

The Hornit attaches to your handle bars vie a mount with a cateye type bracket, take a  second look it appears to use a slightly different tightening mechanism which is an improvement. It tightens via a hex key which appears to be very solid and the rubber grip of the strap allows the bracket to hold well on both road and any other handle bars

Bracket for the mount, and the Hex key

So whats in the Box, and what a great thought out design of a box it is, I liked the way the horn was displayed in side, you can see how much thought went into the design of the packaging.

1 X  Instruction sheet
1 X  Hex Key
1 X  Hornit horn
1 X  Micro switch
1 X  Connector wire
1  X Battery's
1 x Note reminder   

First thing to do was fit the battery's as directed in the very well thought out instructions leaflet, a simple case of a small screw, and you had access to the battery compartment on the horn.
What we then needed was to now fit to the bike!
I removed the old bell fitted, gave the handle bars a little clean up, and offered the horn up to see where it would sit, I decided on the left side of my bars.

Hornit being offers up into position.

I made sure it was not to far from the Micro switch, and then fitted the Mount, a nice bit of rubber held it in place to stop it from slipping, and tightened the clamp with the hex key.
Next thing was to fit the micro switch in place where it was close to pres, at first, I fitted it passed the hand grip, Then wound the wire round the handle bars to take up the slack, and connected the plug,  this was pushed all the way in as recommend on a slip of paper that was in the box, a quick test with a push of the button, and hey presto! One Loud Horn! and I do mean Loud!
It has 2 settings, a loud trill, and a slightly lower piercing sound, more suitable to cycle paths to warn pedestrians that you are approaching, the two tones are very easily changed by a little button on the back of the horn, press it and it changes tone.

I Took it out for a test ride, and it wasn't long before I had to use it in anger! Cars now know you are there, a car went to pull out, not too sure if he saw me, but a quick blast on the Hornit and he knew I was there!
Same with pedestrians, they walk along aimlessly on your part of the cycle track, a press on the Hornit and they turn around!
Found it brilliant when approaching a T crossing on a cycle path, a blast to warn other, and safe to proceed.

So, fits great on a straight bar bike, but how about a road bike!
A look on the instruction sheet on how to fir to road bars, and off I went to try.

First off, find the place it will sit on the handle bars, remove the old bell, place the Micro switch where your finger can press it easily, I found the right hand was more comfortable.

Micro switch fitted to the hood

I then checked on the length of cable from switch to the horn, I found I had more than enough, so, I mounted the clamp and tightened it with the hex key.

Now comes the bit some might not be too comfortable on doing, if this is the case, take your road bike to your nearest local bike shop for them to do it, as you will need to unwrap the part of the bar tape to cover the wire, so, find the end of the bar tape, and start to unwind the tape.

 Find the start
 Unravel the bar tape

 Place the wire on the handle bars and rewind bar tape tight
 Seal up the end of the tape again to stop it coming unwrapped
 Hornit in place
Micro switch
End result!

This only took about 15 minutes to do, it is that simple to fit the Hornit.

On a social ride on Sunday, it was shown to other cyclists, and in the words of Sam Snelling, who I can Quote, "Thats Amazing, well impressed".

The Summing Up!

Don't leave home with out one! 
Until you have one fitted, you wont realise just how easy it is to let other road users and pedestrians know you are there, a quick press of the button, a loud sound is omitted, and you get noticed, as simple as that, if you only have one horn, make it the Hornit, top quality, great service from the people at Hornit.

Simply a Must have product, highly reckoned this horn to every cyclist out there! .


Since fitting the Hornit to the Road bike, I had full use of it on the London to Brighton Bike ride on Sunday the 15th June, came in so useful as there were a lot of cyclists not keeping to the left!
And also it was great fun blasting away on it when the children were  standing with mum and dad all cheering us on and wanting all the passing cyclist to ring there bells, you can imagine there delight to hear the Hornit!

Fantastic horn, cant wait to get out there again and blast away! 

The Hornit on the London To Brighton Bike Ride 15th June 2014

Some Video Links to the Hornit Horn

 Critical Mass Ride in August Filmed with the Blast 

Here is one for the Younger riders out there!
Xmas is coming up soon!


Check them out at Lee Vally Cycles at The Stow in Harlow


From a cyclist out there...
"These guys are the nuts, product is fantastic, and the customer service is second to none. Never known service like it. Cheers guys!"

Foot Note This is not a Paid Advertisement for The Hornit 

No comments:

Post a comment

Please do leave a comment

Peatys Tyre Sealant for cycles.

Peatys Tyre Sealant Review  https://peatys.co.uk/ Welcome to my follow on review blog on the Tubeless Tyre Sealant, I’ve decided to change f...